Shop by Categories
Wholesale: $16.18
Case of 200 Units: $3300.00 $3172.00
Buy in App

Scan the product's code to buy directly.

Follow the below steps:

1.Go to Google and Apple market download install app

2.Open SUNSKY App and scan the left QR code

SUNSKY Free App
   ≥ 1 unit $16.50  
   ≥ 2 units $16.34  
   ≥ 1/4 case $16.18  
   ≥ 1/2 case $16.02  
   ≥ 1 case $15.86  
   ≥ 4 cases $15.69  
   ≥ 10 cases $15.53  
Options:  
Buy in Bulk
Add to Basket
Check Out
Country/Region:
Shipping Cost:   by
More Methods
Carrier Shipping Cost Transit Time
Avatar
Sales Manager: Ms. Miffy
+86-15216126587
We always strive to achieve low prices and good quality, and promised insured and return service.
View after-sales terms
IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
Item #: IP7G7780B
BUY TOGETHER, GET EXTRA DISCOUNT
HINT: If you buy them together, you'll enjoy both the normal discount and the extra discount. The normal discount is calculated from the basket amount and the last 180-day orders. Please check the details in basket.

Featured Products

Repair & Spare Parts

Recently Viewed

FREE GIFT (We'll ship the item with the free gift below)

Description



About the product
1. Replacement LCD screen + touch screen digitizer assembly for iPhone 7.
2. Replace the old, broken, cracked, damaged one.
3. Make your device look more refreshing than ever.
4. Completely fit and work.
5. Each item has been checked and in good condition before shipping.
6. Professional installation is highly recommended. We will not be responsible once the screen is installed.

Before Installation Notes
Tips 1: Test before installation
When testing, do not remove any protective film or tags. Please pay attention to the problem of static electricity.
Before attempting any repair, be sure to ground yourself is an ESD (electro static discharge) strap. This will prevent static electricity from damaging the electronic components within the phone.
Ensure you wear eye protection and use caution not to cut your finger with the glass splinters.
Tips 2: Simulates testing
Screen replacement is very fragile product. We strongly suggest test before installation. Please simulates testing, which means mobile phone apart, (motherboard + LCD or screen) connected audio cable and new replacement, power on, test finished. If test OK, please install it. If it can not show, please contact us at the very first time. And please do not force it to be installed in mobile phone. We will not be responsible once the screen is installed.
Tips 3: Do not over-bend cable
Please make sure LCD cable Do not over-bend. Over 90 degrees bent will cause black display.

Advantages
1. Large stock, fast delivery, can meet large purchasing plan
2. Original top quality.
3. Complete fit and work
4. Supply quality warranty with professional service

Specification:
General
Compatible with
Package Weight
One Package Weight 0.11kgs / 0.23lb
Qty per Carton 200
Carton Weight 13.00kgs / 28.66lb
Carton Size 48cm * 38cm * 27cm / 18.9inch * 14.96inch * 10.63inch
Loading Container 20GP: 541 cartons * 200 pcs = 108200 pcs
40HQ: 1257 cartons * 200 pcs = 251400 pcs
Best Sellers Rank
#75 in category: Repair & Spare Parts
#5 in category: Repair & Spare Parts »  iPhone 7 Parts
#3 in category: Repair & Spare Parts »  iPhone 7 Parts »  LCD Screen
LCD is Bubble Bag Protected, we will not offer warranty for installation.

More Pictures

IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
We will ship this free gift with the order together:
SP6904

GUIDE: iPhone 7 / 7 Plus Screen and Digitizer Replacement

Use this guide to replace a cracked front panel or a broken LCD. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Pentalobe Screws

  • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
  • Power off your iPhone before beginning disassembly.
  • Opening the iPhone's display will damage its waterproof seals. If you do not replace the seals, your phone will no longer be water resistant.
  • Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

Step 2 - Taping Over The Display

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
  • Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.
  • If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.

Step 3 - Opening Procedure

  • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
  • Use a hairdryer or Adhesive Melting Bag and apply it to the lower edge of the phone for about 90 seconds in order to soften up the adhesive underneath.

Step 4

  • Attach a suction cup to the lower half of the display assembly, just above the home button.
  • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Step 5

  • Pull up on the suction cup to create a small gap between the display assembly and the rear case.
  • Insert the flat end of a spudger into the gap.
  • The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside

Step 6

  • Slide the spudger to the left along the lower edge of the iPhone.
  • Twist the spudger to widen the gap between the display and rear case.

Step 7

  • Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.
  • Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

Step 8

  • Insert the flat edge of a spudger into the bottom right corner of the device.
  • Twist the spudger to widen the gap between the display assembly and the rear case.
  • Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.

Step 9

  • Pull up on the suction cup to lift up the display and open the iPhone.
  • Do not raise the display more than 10 Degree as there are ribbon cables along the right edge of the device connecting the display to the logic board.

Step 10

  • Pull up on the small nub on the suction cup to remove it from the front panel.

Step 11

  • Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.
  • Be careful not to damage the plastic clips on the top edge of the phone.

Step 12

  • Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.
  • Open the iPhone by swinging the display up from the left side, like the back cover of a book.
  • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

Step 13 - Battery Disconnection

  • Remove four tri-point Y000 screws securing the lower connector bracket, of the following lengths:
    Three 1.2 mm screws
    One 2.4 mm screw
  • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
  • Remove the lower connector bracket.

Step 14

  • Use the point of a spudger to lift the battery connector out of its socket on the logic board.

Step 15 - Display Assembly

  • Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.
  • Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
  • To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
  • If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Step 16

  • Remove the two 1.3 mm Phillips screws securing the bracket over the front panel sensor assembly connector.
  • Remove the bracket.

Step 17

  • Disconnect the front panel sensor assembly connector from its socket on the logic board.
  • This press connector should also be reconnected one end at a time to minimize the risk of bending.

Step 18

  • Remove the display assembly.
  • During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Reviews

Praise Degree
4.9 stars
4-5 stars:
98%
3 stars:
2%
1-2 stars:
0%
The customers who buy the product and write good quality reviews could obtain 10 SUNSKY Points ($0.20).
Chr*****nro
from Mexico
 
(Most Helpful Review)
06/15/2020 06:16
SUNSKY: Thanks for your order
replied by Miffy
Pop***en
from Finland
 
07/22/2020 07:02
Pop***en
from Finland
 
07/22/2020 07:02
Gabri*****checo
from bahias de huatulco
Mexico
  Order #: 2003096352   Color: Black  
06/26/2020 16:53
Kol***os
from lavrio
Greece
  Order #: 2004215582   Color: Black  
05/08/2020 07:32
Spa****ue5
from Cascais
Portugal
  Order #: 2001215553   Color: Black  
01/23/2020 13:29
Fida*****gora
from Basel
Switzerland
  Order #: 2001015549   Color: Black  
01/10/2020 17:56
De***33
from BRESCIA
Italy
  Order #: 1905122842   Color: White  
11/26/2019 07:28
Geor*****7000
from PARIS 12
France
  Order #: 1910074838   Color: Black  
11/25/2019 17:23
SUNSKY: Thanks for your trust.
replied by peggy
Anselm*****ntino
from Varzea do Poco
Brazil
Order #: 1808175535   Color: Black  
11/12/2019 06:12


Shipping Methods

To list all the shipping costs from different carriers, select the quantity and your country, and then press [Calc].
Country/Region:


We use cookies to ensure that we give you the best experience on our website. By continuing to browse the site, you agree to our use of Cookie I agree

Message

Price Match
item #:
* URL where sold for less:
Remark / Details:
Error Report
item #:
Error URL:
* Type of Error:
Description:
Error Picture:
(gif/jpg/png, 500KB max)
 
 
Arrival Notice Subscription

Item #:
Please leave your email and name, we'll send you email and message as soon as this item is in stock.
* Your Email:
Your Name:
* Qty:
[$16.18] LCD Screen and Digitizer Full Assembly for iPhone 7(Black)
4.9 out of 5 based on 45 user ratings