Shop by Categories
Wholesale: $11.93
Case of 200 Units: $2434.00 $2338.00
Buy in App

Scan the product's code to buy directly.

Follow the below steps:

1.Go to Google and Apple market download install app

2.Open SUNSKY App and scan the left QR code

SUNSKY Free App
   ≥ 1 unit $12.17  
   ≥ 2 units $12.05  
   ≥ 1/4 case $11.93  
   ≥ 1/2 case $11.81  
   ≥ 1 case $11.69  
   ≥ 4 cases $11.57  
   ≥ 10 cases $11.45  
Options:  
Buy in Bulk
Add to Basket
Check Out
Country/Region:
Shipping Cost:   by
More Methods
Carrier Shipping Cost Transit Time
Avatar
Sales Manager: Ms. Emily
+86-13144828556
+86-13144828556
+86-13144828556
We always strive to achieve low prices and good quality, and promised insured and return service.
View after-sales terms
IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
  • IP8F6403W
Item #: IP8F6403W

Featured Products

Repair & Spare Parts

Recently Viewed

FREE GIFT (We'll ship the item with the free gift below)

Description

Before Installation Notes
Tips 1: Test before installation
When testing, do not remove any protective film or tags. Please pay attention to the problem of static electricity.
Before attempting any repair, be sure to ground yourself is an ESD (electro static discharge) strap. This will prevent static electricity from damaging the electronic components within the phone.
Ensure you wear eye protection and use caution not to cut your finger with the glass splinters.
Tips 2: Simulates testing
Screen replacement is very fragile product. We strongly suggest test before installation. Please simulates testing, which means mobile phone apart, (motherboard + LCD or screen) connected audio cable and new replacement, power on, test finished. If test OK, please install it. If it can not show, please contact us at the very first time. And please do not force it to be installed in mobile phone. We will not be responsible once the screen is installed.
Tips 3: Do not over-bend cable
Please make sure LCD cable Do not over-bend. Over 90 degrees bent will cause black display.

Advantages
1. Large stock, fast delivery, can meet large purchasing plan
2. Original top quality.
3. Complete fit and work
4. Supply quality warranty with professional service

About the product
1. Replacement LCD screen + touch screen digitizer assembly for iPhone 8.
2. Replace the old, broken, cracked, damaged one.
3. Make your device look more refreshing than ever.
4. Completely fit and work.
5. Each item has been checked and in good condition before shipping.
6. Professional installation is highly recommended. We will not be responsible once the screen is installed.

Specification:
General
Compatible with
Package Weight
One Package Weight 0.12kgs / 0.26lb
Qty per Carton 200
Carton Weight 13.00kgs / 28.66lb
Carton Size 48cm * 38cm * 27cm / 18.9inch * 14.96inch * 10.63inch
Best Sellers Rank
#109 in category: Repair & Spare Parts
#5 in category: Repair & Spare Parts »  iPhone 8 Parts
#1 in category: Repair & Spare Parts »  iPhone 8 Parts »  LCD Screen
LCD is Bubble Bag Protected, we will not offer warranty for installation.

More Pictures

IP8F6403W
IP8F6403W
IP8F6403W
IP8F6403W
IP8F6403W
IP8F6403W
IP8F6403W
IP8F6403W
We will ship this free gift with the order together:
S-IP5G-0292

GUIDE: iPhone 8 / 8 Plus Display Assembly Replacement

Use this guide to replace a cracked front panel or a broken LCD. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Pentalobe Screws

  • Opening the iPhone's display will damage its waterproof seals. If you do not replace the seals, your phone will no longer be water resistant.
  • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
  • Power off your iPhone before beginning disassembly.
  • Remove the two 3.5 mm pentalobe screws on the bottom edge of the iPhone.

Step 2 - Opening Procedure

  • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
  • Use a hairdryer or Adhesive Melting Bag and apply it to the lower edge of the phone for about 90 seconds in order to soften up the adhesive underneath.

Step 3

  • Apply a suction cup to the lower half of the front panel, just above the home button.
  • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Step 4

  • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
  • Insert an opening pick into the gap.
  • The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

Step 5

  • Slide the opening pick up the left edge of the phone starting at the lower edge and moving towards the volume control buttons and silent switch, breaking up the adhesive holding the display in place.
  • Stop near the top left corner of the display.
  • Do not try to pry the top edge of the display away from the rear case, as it is held in place by plastic clips that may break.

Step 6

  • Re-insert your tool at the lower right corner of the iPhone, and slide it around the corner and up the right side of the phone to separate the adhesive.
  • Don't insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.

Step 7

  • Gently pull up on the suction cup to lift up the bottom edge of the display.
  • Do not raise the display more than 15 Degree or you'll risk straining or tearing the ribbon cables connecting the display.
  • Pull on the small nub on the suction cup to remove it from the front panel.

Step 8

  • Slide an opening pick underneath the display around the top left corner and along the top edge of the phone to loosen the last of the adhesive.

Step 9

  • Slide the display assembly slightly down (away from the top edge of the phone) to disengage the clips holding it to the rear case.
  • Open the iPhone by swinging the display up from the left side, like the back cover of a book.
  • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.
  • Lean the display against something to keep it propped up while you're working on the phone.

Step 10

  • Remove four Phillips screws securing the lower display cable bracket to the logic board, of the following lengths:
    Two 1.3 mm screws
    Two 2.8 mm screws
  • Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.
  • Remove the bracket.

Step 11

  • Use the point of a spudger to pry the battery connector out of its socket in the logic board.
  • Bend the battery connector cable slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Step 12 - Display Assembly

  • Use the point of a spudger to pry the lower display connector out of its socket.
  • To re-attach press connectors like this one, press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
  • Use the point of a spudger to disconnect the second lower display cable.

Step 13

  • Remove the three 1.3 mm Phillips screws securing the bracket over the front panel sensor assembly connector.
  • Remove the bracket.

Step 14

  • Use the point of a spudger to disconnect the front panel sensor assembly connector.
  • Remove the display assembly.
  • During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Reviews

Praise Degree
4.9 stars
4-5 stars:
100%
3 stars:
0%
1-2 stars:
0%
The customers who buy the product and write good quality reviews could obtain 10 SUNSKY Points ($0.20).
Ram****rba
from LA NEUVILLE CHANT D'OISEL
France
  Order #: 1903073937   Color: White  
05/08/2019 11:43
Pol****oyd
from Mondragone
Italy
  Order #: 1903195552   Color: White  
04/14/2019 08:55
Luig*****one
from ROMA
Italy
  Order #: 1903285956   Color: White  
04/09/2019 15:15
Mzu***lo
from Crema (CREMONA)
Italy
  Order #: 1902206431   Color: Black  
04/05/2019 14:23
Pin*****Pro
from Perkasie
U.S.A.
  Order #: 1811226444   Color: White  
12/10/2018 01:23
Ad***nz
from Italy
 
11/01/2018 08:32
Sydn*****ith
from Belgium
  Order #: 1809095325   SKU: IP8F6403B  
09/17/2018 07:07
El**ot
from Lyon
France
  Order #: 1809042810   SKU: IP8F6403B  
09/12/2018 02:55
Ja****hin
from Australia
  Order #: 1808161113   SKU: IP8F6403B  
08/23/2018 22:28
Himan*****umar
from Ukraine
  Order #: 1808151122   SKU: IP8F6403B  
08/23/2018 22:22


Shipping Methods

To list all the shipping costs from different carriers, select the quantity and your country, and then press [Calc].
Country/Region:

Buyer Recommended


Message

Price Match
item #:
* URL where sold for less:
Remark / Details:
Error Report
item #:
Error URL:
* Type of Error:
Description:
Error Picture:
(gif/jpg/png, 500KB max)
 
 
Arrival Notice Subscription

Item #:
Please leave your email and name, we'll send you email and message as soon as this item is in stock.
* Your Email:
Your Name:
* Qty:
[$11.93] LCD Screen and Digitizer Full Assembly for iPhone 8(White)
4.9 out of 5 based on 12 user ratings