Compre por Categorias
Próximo      Anterior
Mail para amigos Adicionar a lista de desejos

iPartsBuy 4 em 1 para iPhone 5 (camera frontal LCD Moldura Touchpad) Assembléia digitador Ship Time Prazos de entrega: 1~3 Dias

Atacado: $10.89
A Caixa de 100 unidades: $1111.00 $1067.00
Compre no APP

Digitalize o código do produto para comprar diretamente.

Siga os passos abaixo:

1.Vá para o Google e o mercado da Apple para baixar e instalar APP

2.Abra o SUNSKY APP e digitalize o código QR esquerdo

SUNSKY App grátis
   ≥ 1 unidade $11.11  
   ≥ 2 Unidades $11.00  
   ≥ 1/4 caixa $10.89  
   ≥ 1/2 caixa $10.78  
   ≥ 1 caixa $10.67  
   ≥ 4 Caixa(s) $10.56  
   ≥ 10 Caixa(s) $10.45  
Opções:  
Compre a granel
Adicionar ao carrinho
Comprar agora
País / Região:
Taxa de transporte:   por
Mais métodos
Empresa de transporte Taxa de transporte Tempo de trânsito
Avatar
Gerente de vendas: Ms. Belle
+86-13422694132
+86-13422694132
+86-13422694132
Nós sempre nos esforçamos para oferecer preço baixo e de boa qualidade, e prometemos pelo serviço do seguro de preço & retorno e substituição do produto.
Verifique os Termos Pós-venda
IP5G2000B
  • IP5G2000B
  • IP5G2000B
  • IP5G2000B
  • IP5G2000B
  • IP5G2000B
  • IP5G2000B
  • IP5G2000B
Item #: IP5G2000B

Produtos em destaque

Peças de Reparação

Visto recentemente

Presente grátis (Nós vamos enviar o item com o presente grátis abaixo)

Descrição

Notas de Antes de Instalação
1. Dicas 1: Teste antes da instalação
Ao testar, não remova nenhum filme ou etiqueta protetora. Por favor, preste atenção para o problema da eletricidade estática.
Antes de tentar qualquer reparo, certifique-se de aterrar a si mesmo é uma tira ESD (descarga eletrostática). Isso evitará que a eletricidade estática danifique os componentes eletrônicos no telefone.
Certifique-se de usar proteção para os olhos e tenha cuidado para não cortar o dedo com as lascas de vidro.
2. Dicas 2: Simula o teste
Substituição de tela é um produto muito frágil. Nós sugerimos fortemente o teste antes da instalação. Por favor, simula o teste, o que significa que o telefone móvel distante, (placa-mãe LCD ou tela) cabo de áudio conectado e nova substituição, ligar, teste terminado. Se o teste estiver OK, instale-o. Se não pode mostrar, entre em contato conosco pela primeira vez. E por favor, não force a instalação no telefone celular. Não nos responsabilizaremos quando a tela estiver instalada.
3. Dicas 3: Não dobre o cabo
Por favor, certifique-se de que o cabo do LCD não se dobre excessivamente. Mais de 90 graus dobrados causarão uma exibição preta.

Vantagens
1. Grande estoque, entrega rápida, pode atender grande plano de compras
2. Qualidade superior original.
3. Ajuste completo e trabalho
4. Forneça a garantia da qualidade com o serviço profissional

Sobre o produto
1. Tela LCD da recolocação com tecla home para o iPhone 5
2. Substitua a tela LCD velha, quebrada, rachada, danificada por uma nova
3. Faça seu dispositivo parecer mais refrescando do que nunca
4 Completamente ajuste e trabalho
5. Cada item foi verificado e em boas condições antes do envio
6. A instalação profissional é altamente recomendada. Não nos responsabilizaremos quando a tela estiver instalada.

Especificação:
Universal
Compatível com
Especificações comuns
Tamanho 121 * 57 * 5 mm
Peso 41 g
Peso do pacote
Peso de produto individual 0.11kgs / 0.24lb
Quantidade por caixa 100
Peso da caixa 8.50kgs / 18.74lb
Tamanho da caixa 45cm * 35cm * 30cm / 17.72inch * 13.78inch * 11.81inch
Classificação dos melhores vendedores
#3885 Categoria: Peças de Reparação
#11 Categoria: Peças de Reparação »  Peças para iPhone 5
#3 Categoria: Peças de Reparação »  Peças para iPhone 5 »  LCD Tela
LCD is Bubble Bag Protected, we will not offer warranty for installation.

Mais imagens

IP5G2000B
IP5G2000B
IP5G2000B
IP5G2000B
IP5G2000B
IP5G2000B
IP5G2000B
Enviaremos este presente grátis com o pedido:
S-IP5G-0292

GUIA: iPhone 5 Front Panel Replacement

Use this guide to replace your iPhone's cracked or otherwise damaged front panel. The front panel does not come with the home button, front camera assembly, earpiece speaker, or the LCD shield plate. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Display Assembly

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
  • Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.

Step 2

  • Before disassembling your iPhone, be sure it is powered off.
  • Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.

Step 3 - LCD Screen Opener Opening Procedure

  • The next two steps demonstrate using the LCD Screen Opener, a great tool for safely opening the iPhone 5 that we recommend for anyone doing more than one repair. If you aren't using the LCD Screen Opener, skip to step 5.
  • Close the handle on the LCD Screen Opener, opening the suction-cup jaws.
  • Place the bottom of your iPhone in between the suction cups, against the plastic depth gauge.
  • The top suction cup should rest just above the home button.
  • Open the handles to close the jaws of the LCD Screen Opener. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

Step 4

  • Hold onto your iPhone securely and close the handle of the LCD Screen Opener to separate the suction cups, pulling the front panel up from the rear case.
  • The LCD Screen Opener is designed to safely open your iPhone just enough to separate the pieces, but not enough to damage the home button cable.
  • Peel the two suction cups off your iPhone.
  • Skip the next three steps and continue on step 7.

Step 5

  • Press a suction cup onto the screen, just above the home button.
  • Be sure the cup is completely on the screen to get a tight seal.
  • If you're opening an iPhone with cracked glass, neatly lay a couple strips of packing tape across the front and squeeze out as many bubbles as you can. This will give the suction cup a surface to grab, and minimize the spread of broken glass.

Step 6

  • Make sure the suction cup is firmly attached to the front panel assembly.
  • While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.
  • Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices.
  • With a plastic opening tool, begin to gently pry the rear case down, away from the display assembly, while you pull up with the suction cup.
  • There are several clips attaching the front panel assembly to the rear case, so you may need to use a combination of the suction cup and plastic opening tool to free the front panel assembly.

Step 7

  • Continue to pry up around the sides of the front panel assembly, detaching the clips along the left and right side.

Step 8

  • Do not try to completely remove the front panel assembly from the rear case, as there are several ribbon cables still attached at the top of the iPhone.
  • Be sure to disconnect the battery first before proceeding with the repair as not doing so can sometimes cause the phone to run hot and/or have issues with touch sensitivity.
  • Once the clips have been released on the bottom and sides of the front panel assembly, pull the bottom of the assembly away from the rear case.
  • Lift the front panel assembly slowly up to about 90 degrees from the rear case.

Step 9

  • Remove the following screws securing the front panel assembly cable bracket to the logic board:
  • Two 1.2 mm Phillips screws
  • One 1.6 mm Phillips screw
  • This screw tends to not be attracted to a magnetized screwdriver. Take care not to lose it when removing, and make sure it gets back into the right place—a magnetized screw may interfere with the compass.

Step 10

  • Remove the front panel assembly cable bracket from the logic board.
  • Note: To ensure correct installation, make sure you clip the small hooks of the bracket under and then lower towards the outside of the phone.

Step 11

  • Use a plastic opening tool to disconnect the three front panel assembly cables:
  • Front-facing camera and sensor cable
  • LCD cable
  • Digitizer cable
  • When reassembling your phone, The LCD cable may pop off the connector. This can cause white lines, or nothing at all to appear when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery.

Step 12

  • Remove the front panel assembly from the rear case.

Step 13 - Earpiece Speaker

  • Remove two screws securing the front-facing camera bracket to the display assembly.
  • One 4.1 mm Phillips screw
  • One 2.2 mm Phillips screw

Step 14

  • There is a small, black plastic spacer underneath the metal bracket at the upper screw. The upper screw goes through the metal bracket then through this plastic spacer.

Step 15

  • Remove the earpiece speaker bracket from the display assembly.

Step 16

  • Remove the earpiece speaker from the iPhone.

Step 17 - Front-Facing Camera and Sensor Cable

  • Starting under the earpiece speaker contacts, use a plastic opening tool or the tip of a spudger to pry the front facing camera cable out of the display assembly.
  • Caution: Removing the earpiece speaker contacts can cause them to tear. Use extreme caution when peeling the contacts up.

Step 18

  • Remove the front-facing camera and rear microphone assembly.
  • If you are installing a new part, your new part may have two tabs with holes in it used for manufacturing purposes. These tabs can be cut off with scissors.
  • There is a small, square plastic and metal holder for the proximity sensor. This holder is essential for the proximity sensor to function correctly.
  • If replacing the proximity sensor or camera make sure that the holder remains adhered to the back of the display. If it comes off with the old proximity sensor, remove it from the old sensor and use a tiny bit of adhesive to re-attach it to the back of the display.

Step 19 - Home Button Ribbon Cable

  • Remove the two 1.3 mm Phillips #000 screws securing the home button bracket to the display assembly.
  • NOTE: When reinstalling the two 1.3 mm Phillips #000 screws, take care not to over tighten them as they can penetrate the other side of the display.

Step 20

  • Use a plastic opening tool to pry the edge of the home button ribbon cable up from the display assembly.
  • Start on the right, at the area of the ribbon cable between the gold contact points, and work to the left.
  • Going left to right may rip your ribbon cable as the contacts are well adhered to the front panel.
  • Prying directly at one gold contact point or the other may break its soldering and pop it off the ribbon cable.
  • If you have trouble sliding the plastic opening tool under the contact points, flip the tool over and gently push against the right side of the contacts to loosen the adhesive, then try again.

Step 21 - Front Panel

  • Use a plastic opening tool to pry the home button up from the display assembly.

Step 22

  • Remove the home button from the display assembly.

Step 23

  • Remove two 1.2 mm Phillips screws from each side of the LCD frame (four total).

Step 24

  • Remove the two screws securing the LCD shield plate to the display assembly:
  • One 1.4 mm Phillips screw
  • One 2.6 mm Phillips screw

Step 25

  • Remove the LCD shield plate from the display assembly.

Step 26

  • The bare display assembly remains.
  • For reassembly, make sure to transfer over the LCD shield, home button, front facing camera assembly, front facing camera lens bezel and earpiece speaker to your new part.
  • Make sure to remove the protective cover from your new display assembly as well as the protective cover on the back of the LCD.
  • Note: When reassembled, the screen may not turn on. Try fixing this by plugging your phone in, and holding down the power and home buttons at the same time for 20 seconds.

Comentários

Grau de Louvor
4.7 estrelas
4-5 estrelas:
96%
3 estrelas:
4%
1-2 estrelas:
0%
Os clientes que compram o produto e escrevem comentário de boa qualidade podem obter 10 SUNSKY Pontos ($0.20).
Kol***os
from lavrio
Greece
  Order #: 1908115563   Color: White  
08/24/2019 05:35
Ta****166
from khulais
Saudi Arabia
  Order #: 1703010641   Color: Black  
08/06/2019 07:46
Jo**96
from Catania
Italy
  Order #: 1901041594   Color: White  
02/28/2019 05:36
K.pa*****umar
from France
01/04/2019 18:14
Ibrahi*****5matir
from Saudi Arabia
11/29/2018 07:29
Red***ds
from Praha 6
Czech
  Order #: 1810036335   Color: White  
11/08/2018 05:04
Jo**96
from Catania
Italy
  Order #: 1808301581   Color: White  
09/20/2018 07:40
Mas****n83
from UDINE
Italy
  Order #: 1808218032   Color: Black  
08/27/2018 05:30
Luig*****one
from ROMA
Italy
  Order #: 1806215931   Color: White  
08/19/2018 18:22
De***33
from BRESCIA
Italy
  Order #: 1612272835   Color: White  
10/12/2017 13:11


Métodos de Envio

Para listar todos os custos de envio de portadores diferentes, selecione a quantidade e seu país e, em seguida, pressione [Calc].
País / Região:

Recomendado pelo comprador


Mensagem

Correspondência de preço
item #:
* URL onde foi vendido por menos:
Observação / Detalhes:
Relatório de erros
item #:
URL de erro:
* Tipo de erro:
Descrição:
Imagem de erro:
(gif/jpg/png, 500KB max)
 
 
Assinatura do aviso de chegada

Item #:
Por favor deixe o seu e-mail e nome, nós lhe enviaremos e-mail e mensagem assim que este item está em estoque.
* Seu e-mail:
Seu nome:
* Qtd:
[$10.89] iPartsBuy 4 em 1 para iPhone 5 (camera frontal LCD Moldura Touchpad) Assembléia digitador
4.7 fora 5 com base nas 374 avaliações do usuário