发邮件给朋友
添加到收藏夹
所有类别
» 维修配件
» iPhone7维修配件
» 液晶屏
4.7英寸 iPhone 7 友达 国产液晶屏总成
发货时间: 1~3 天
批发:
$10.57
一箱200个:
$2156.00
$2072.00


≥ 1 个 | $10.78 |
≥ 2 个 | $10.68 |
≥ 1/4 箱 | $10.57 |
≥ 1/2 箱 | $10.46 |
≥ 1 箱 | $10.36 |
≥ 4 箱 | $10.25 |
≥ 10 箱 | $10.15 |
![]() |
销售经理: Ms. Yoyo
|
|
+86-15817361427
|
||
|
我们一直努力做到低价和好的品质,并承诺保价和退换货服务。 查看售后条款 |
热门产品
特色产品
维修配件
最近浏览

描述
关于产品
1. 用于iPhone 7的替换LCD屏幕 触摸屏数字转换器组件。
2. 更换旧的,破损的,破裂的,损坏的。
3. 让您的设备看起来比以往更清晰。
4. 完全适合。
5. 每件商品在发货前都经过检查并处于良好状态。
6. 强烈建议专业安装。一旦安装了屏幕,我们将不负责任。
安装前注意事项
1. 安装前
测试时,请勿取下任何保护膜或标签。请注意静电问题。
在尝试任何修理之前,请确保自己接地是ESD(静电放电)带。这将防止静电损坏手机内的电子元件。
确保您戴上护目镜并小心不要用玻璃碎片割伤手指。
2. 模拟测试
屏幕总成是非常脆弱的产品。我们强烈建议在安装前进行模拟测试,(主板 LCD或屏幕)连接音频线和新的更换,开机,测试完成。如果测试正常,请安装它。如果无法显示,请在第一时间联系我们。请不要强迫它安装在手机上。一旦安装了屏幕,我们将不负责任。
3. 不要过度弯曲电缆
请确保LCD电缆不要过度弯曲。弯曲超过90度将导致黑屏。
优点
1. 库存量大,交货快,可满足大量采购计划
2. 原装顶级品质。
3. 完整的配合和工作
4. 提供专业的服务质量保证
1. 用于iPhone 7的替换LCD屏幕 触摸屏数字转换器组件。
2. 更换旧的,破损的,破裂的,损坏的。
3. 让您的设备看起来比以往更清晰。
4. 完全适合。
5. 每件商品在发货前都经过检查并处于良好状态。
6. 强烈建议专业安装。一旦安装了屏幕,我们将不负责任。
安装前注意事项
1. 安装前
测试时,请勿取下任何保护膜或标签。请注意静电问题。
在尝试任何修理之前,请确保自己接地是ESD(静电放电)带。这将防止静电损坏手机内的电子元件。
确保您戴上护目镜并小心不要用玻璃碎片割伤手指。
2. 模拟测试
屏幕总成是非常脆弱的产品。我们强烈建议在安装前进行模拟测试,(主板 LCD或屏幕)连接音频线和新的更换,开机,测试完成。如果测试正常,请安装它。如果无法显示,请在第一时间联系我们。请不要强迫它安装在手机上。一旦安装了屏幕,我们将不负责任。
3. 不要过度弯曲电缆
请确保LCD电缆不要过度弯曲。弯曲超过90度将导致黑屏。
优点
1. 库存量大,交货快,可满足大量采购计划
2. 原装顶级品质。
3. 完整的配合和工作
4. 提供专业的服务质量保证
规格与包装:
包裹重量 |
|
销量排名 |
|
LCD is Bubble Bag Protected, we will not offer warranty for installation.
指南: iPhone 7 / 7 Plus Screen and Digitizer Replacement
Use this guide to replace a cracked front panel or a broken LCD. To reassemble your device, follow these instructions in reverse order.
Tools
Parts
- LCD Screen and Digitizer Full Assembly for iPhone 7
- Front Screen Outer Glass Lens with Front LCD Screen Bezel Frame for iPhone 7
- Front Facing Camera for iPhone 7
- Charging Port + Audio Flex Cable for iPhone 7
- 100 PCS for iPhone 7 Repair Tools Complete Screws / Bolts Set
- LCD Screen and Digitizer Full Assembly for iPhone 7 Plus
- Front Screen Outer Glass Lens with Front LCD Screen Bezel Frame for iPhone 7 Plus
- Charging Port Flex Cable for iPhone 7 Plus
- 10 PCS for iPhone 7 & 7 Plus Charging Port Screws

Step 1 - Pentalobe Screws
- Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
- Power off your iPhone before beginning disassembly.
- Opening the iPhone's display will damage its waterproof seals. If you do not replace the seals, your phone will no longer be water resistant.
- Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

Step 2 - Taping Over The Display
- If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
- Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
- This will keep glass shards contained and provide structural integrity when prying and lifting the display.
- Wear safety glasses to protect your eyes from any glass shaken free during the repair.
- If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.

Step 3 - Opening Procedure
- Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
- Use a hairdryer or Adhesive Melting Bag and apply it to the lower edge of the phone for about 90 seconds in order to soften up the adhesive underneath.

Step 4
- Attach a suction cup to the lower half of the display assembly, just above the home button.
- Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Step 5
- Pull up on the suction cup to create a small gap between the display assembly and the rear case.
- Insert the flat end of a spudger into the gap.
- The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside

Step 6
- Slide the spudger to the left along the lower edge of the iPhone.
- Twist the spudger to widen the gap between the display and rear case.

Step 7
- Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.
- Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

Step 8
- Insert the flat edge of a spudger into the bottom right corner of the device.
- Twist the spudger to widen the gap between the display assembly and the rear case.
- Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.

Step 9
- Pull up on the suction cup to lift up the display and open the iPhone.
- Do not raise the display more than 10 Degree as there are ribbon cables along the right edge of the device connecting the display to the logic board.

Step 10
- Pull up on the small nub on the suction cup to remove it from the front panel.

Step 11
- Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.
- Be careful not to damage the plastic clips on the top edge of the phone.

Step 12
- Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.
- Open the iPhone by swinging the display up from the left side, like the back cover of a book.
- Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

Step 13 - Battery Disconnection
- Remove four tri-point Y000 screws securing the lower connector bracket, of the following lengths:Three 1.2 mm screwsOne 2.4 mm screw
- Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
- Remove the lower connector bracket.

Step 14
- Use the point of a spudger to lift the battery connector out of its socket on the logic board.

Step 15 - Display Assembly
- Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.
- Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
- To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
- If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Step 16
- Remove the two 1.3 mm Phillips screws securing the bracket over the front panel sensor assembly connector.
- Remove the bracket.

Step 17
- Disconnect the front panel sensor assembly connector from its socket on the logic board.
- This press connector should also be reconnected one end at a time to minimize the risk of bending.

Step 18
- Remove the display assembly.
- During reassembly, pause here if you wish to replace the adhesive around the edges of the display.
评论
平均分
4.9 星
|
|
购买这个产品并撰写高质量的评论可以获得10SUNSKY积分($0.20).
|

Red***ds
from Praha 6
Czech
Czech
Order #: 1901096351
Color: Black
(最有帮助的评论)
04/10/2019 15:06

S**b2
from ابها
Saudi Arabia
Saudi Arabia
Order #: 1811141531
Color: White
(最有帮助的评论)
12/18/2018 00:57

De***33
from BRESCIA
Italy
Italy
Order #: 1905122842
Color: White
11/26/2019 07:28

Geor*****7000
from PARIS 12
France
France
Order #: 1910074838
Color: Black
11/25/2019 17:23
SUNSKY: Thanks for your trust.
回复者
peggy


Anselm*****ntino
from Varzea do Poco
Brazil
Brazil
Order #: 1808175535
Color: Black
11/12/2019 06:12

Eug*****984
from roma
Italy
Italy
Order #: 1804302536
Color: Black
10/10/2019 04:27

Eug*****984
from roma
Italy
Italy
Order #: 1805242534
Color: Black
10/08/2019 05:13

Eug*****984
from roma
Italy
Italy
Order #: 18122825153
Color: Black
10/08/2019 04:34

Eug*****984
from roma
Italy
Italy
Order #: 1901052539
Color: Black
10/08/2019 04:32

Eug*****984
from roma
Italy
Italy
Order #: 1904292555
Color: Black
10/08/2019 04:15
买家推荐
-
HAMTOD HKJ400 高清 运动摄像机凌通6624方案
批发: $10.72 -
iPhone 5s & 5C 触摸IC芯片 343S0645
批发: $1.23 -
iPad 2 16GB Wifi版本后壳
批发: $11.07 -
1m USB-C / Type-C to 8 Pin PD Fast Charging Cable, Cable Length: 1m
批发: $3.09 -
ENKAY 草帽王子 三星 盖乐世A5 (2017) / A520 0.26mm厚度 9H表面硬度 2.5D弧边全屏钢化玻璃彩膜 (黑色)
批发: $1.70 -
三星 Galaxy A20 液晶触摸总成 (黑色)
批发: $85.96 -
LCD Screen and Digitizer Full Assembly with Frame for Lenovo S90 S90-T S90-U S90-A (Black)
批发: $29.36 -
LCD Screen and Digitizer Full Assembly with Frame for Lenovo K6 Power (White)
批发: $13.13 -
小米 Redmi 7 黑屏模型机 (黑色)
批发: $5.48 -
2.5D 全胶全屏陶瓷贴膜 适用于 iPhone 8 / 7 (黑色)
批发: $0.75 -
美特柏 小米Xiaomi Redmi Note 7 丝印二强 全屏全胶防指纹钢化膜 (黑色)
批发: $0.68 -
PULUZ U6000 Novatek 96650高清运动数码摄像机 带WiFi
批发: $22.00买10送1 -
液晶屏玻璃保护罩适用于尼康D800
批发: $2.31 -
130万像素插值翻转屏微单数码相机,2.4英寸LCD屏,红外镜头
批发: $27.715% OFF Coupon ASD95
-
50颗led像素模块数字独立可寻址全彩灯串防水IP65
批发: $8.23