產品類別
批發: $10.57
一箱200個: $2156.00 $2072.00
在App中購買

掃描產品的二維碼直接購買。

按照以下步驟操作:

1.轉到Google和Apple市場下載安裝應用

2.打開SUNSKY App並掃描左側二維碼

SUNSKY APP
   ≥ 1 個 $10.78  
   ≥ 2 個 $10.68  
   ≥ 1/4 箱 $10.57  
   ≥ 1/2 箱 $10.46  
   ≥ 1 箱 $10.36  
   ≥ 4 箱 $10.25  
   ≥ 10 箱 $10.15  
選項:  
批量購買
添加到購物車
立即購買
國家/地區:
運費:   運輸方式:
其它方式
快遞 運費 運輸時間
銷售經理: Ms. Alisa
+86-13242088884
我們一直努力做到低價和好的品質,並承諾保價和退換貨服務。
查看售後條款
IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
  • IP7G7780B
產品型號: IP7G7780B
Click Count 16721 點擊次數

特色產品

維修配件

最近瀏覽

免費禮物 (禮品將和當前產品一起發送)

描述



關於產品
1. 用於iPhone 7的替換LCD屏幕 觸摸屏数字轉換器組件。  
2. 更換舊的,破損的,破裂的,損壞的。
3. 讓您的設備看起來比以往更清晰。 
4. 完全適合。
5. 每件商品在發貨前都經過檢查並處於良好狀態。
6. 強烈建議專業安裝。一旦安裝了屏幕,我們將不負責任。

安裝前注意事項
1. 安裝前
測試時,請勿取下任何保護膜或標籤。請注意靜電問題。
在嘗試任何修理之前,請確保自己接地是ESD(靜電放電)帶。這將防止靜電損壞手機內的电子元件。
確保您戴上護目鏡並小心不要用玻璃碎片割傷手指。
2. 模擬測試
屏幕總成是非常脆弱的產品。我們強烈建議在安裝前進行模擬測試,(主板 LCD或屏幕)連接音頻線和新的更換,開機,測試完成。如果測試正常,請安裝它。如果無法显示,請在第一時間聯繫我們。請不要強迫它安裝在手機上。一旦安裝了屏幕,我們將不負責任。
3. 不要過度彎曲電纜
請確保LCD電纜不要過度彎曲。彎曲超過90度將導致黑屏。

優點
1. 庫存量大,交貨快,可滿足大量採購計劃
2. 原裝頂級品質。
3. 完整的配合和工作
4. 提供專業的服務質量保證

規格與包裝:
通用
兼容性
包裹重量
單個產品重量 0.11kgs / 0.23lb
装箱数量 200
整箱重量 13.00kgs / 28.66lb
整箱尺寸 48cm * 38cm * 27cm / 18.9inch * 14.96inch * 10.63inch
銷量排名
#6 所屬類別: 維修配件
#1 所屬類別: 維修配件 »  iPhone7維修配件
#1 所屬類別: 維修配件 »  iPhone7維修配件 »  LCD屏
LCD is Bubble Bag Protected, we will not offer warranty for installation.

更多圖片

IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
IP7G7780B
禮品將與訂單一起發送:
S-IP5G-0292

指南: iPhone 7 / 7 Plus Screen and Digitizer Replacement

Use this guide to replace a cracked front panel or a broken LCD. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Pentalobe Screws

  • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
  • Power off your iPhone before beginning disassembly.
  • Opening the iPhone's display will damage its waterproof seals. If you do not replace the seals, your phone will no longer be water resistant.
  • Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

Step 2 - Taping Over The Display

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
  • Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.
  • If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.

Step 3 - Opening Procedure

  • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
  • Use a hairdryer or Adhesive Melting Bag and apply it to the lower edge of the phone for about 90 seconds in order to soften up the adhesive underneath.

Step 4

  • Attach a suction cup to the lower half of the display assembly, just above the home button.
  • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Step 5

  • Pull up on the suction cup to create a small gap between the display assembly and the rear case.
  • Insert the flat end of a spudger into the gap.
  • The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside

Step 6

  • Slide the spudger to the left along the lower edge of the iPhone.
  • Twist the spudger to widen the gap between the display and rear case.

Step 7

  • Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.
  • Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

Step 8

  • Insert the flat edge of a spudger into the bottom right corner of the device.
  • Twist the spudger to widen the gap between the display assembly and the rear case.
  • Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.

Step 9

  • Pull up on the suction cup to lift up the display and open the iPhone.
  • Do not raise the display more than 10 Degree as there are ribbon cables along the right edge of the device connecting the display to the logic board.

Step 10

  • Pull up on the small nub on the suction cup to remove it from the front panel.

Step 11

  • Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.
  • Be careful not to damage the plastic clips on the top edge of the phone.

Step 12

  • Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.
  • Open the iPhone by swinging the display up from the left side, like the back cover of a book.
  • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

Step 13 - Battery Disconnection

  • Remove four tri-point Y000 screws securing the lower connector bracket, of the following lengths:
    Three 1.2 mm screws
    One 2.4 mm screw
  • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
  • Remove the lower connector bracket.

Step 14

  • Use the point of a spudger to lift the battery connector out of its socket on the logic board.

Step 15 - Display Assembly

  • Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.
  • Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
  • To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
  • If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Step 16

  • Remove the two 1.3 mm Phillips screws securing the bracket over the front panel sensor assembly connector.
  • Remove the bracket.

Step 17

  • Disconnect the front panel sensor assembly connector from its socket on the logic board.
  • This press connector should also be reconnected one end at a time to minimize the risk of bending.

Step 18

  • Remove the display assembly.
  • During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

評論

平均分
4.9 星
4-5 星:
98%
3 星:
2%
1-2 星:
0%
購買這個產品並撰寫高質量的評論可以獲得10SUNSKY積分($0.20).
Red***ds
from Praha 6
Czech
  Order #: 1901096351   Color: Black  
(最有幫助的評論)
04/10/2019 15:06
S**b2
from ابها
Saudi Arabia
  Order #: 1811141531   Color: White  
(最有幫助的評論)
12/18/2018 00:57
De***33
from BRESCIA
Italy
  Order #: 1905122842   Color: White  
11/26/2019 07:28
Geor*****7000
from PARIS 12
France
  Order #: 1910074838   Color: Black  
11/25/2019 17:23
SUNSKY: Thanks for your trust.
回復者 peggy
Anselm*****ntino
from Varzea do Poco
Brazil
Order #: 1808175535   Color: Black  
11/12/2019 06:12
Eug*****984
from roma
Italy
  Order #: 1804302536   Color: Black  
10/10/2019 04:27
Eug*****984
from roma
Italy
  Order #: 1805242534   Color: Black  
10/08/2019 05:13
Eug*****984
from roma
Italy
  Order #: 18122825153   Color: Black  
10/08/2019 04:34
Eug*****984
from roma
Italy
  Order #: 1901052539   Color: Black  
10/08/2019 04:32
Eug*****984
from roma
Italy
  Order #: 1904292555   Color: Black  
10/08/2019 04:15


運輸方式

請選擇數量和所在國家/地區,然後按[計算]。可以得到不同運輸方式的價格
國家/地區:


消息

發現價格
產品型號:
* 以較低價格出售的網址:
備註/詳細信息:
錯誤報告
產品型號:
錯誤網址:
* 輸入錯誤:
說明:
錯誤圖片:
(gif/jpg/png, 500KB max)
 
 
到貨通知訂閱

產品型號:
請留下您的电子郵件和姓名,我們會在此商品有貨時立即向您發送电子郵件和留言。
* 您的Email:
您的姓名:
* 數量:
[$10.57] 4.7英寸 iPhone 7 友達 國產液晶屏總成
4.9 超出 5 基於 38 用戶評分