產品類別
批發: $10.66
一箱200個: $2174.00 $2090.00
在App中購買

掃描產品的二維碼直接購買。

按照以下步驟操作:

1.轉到Google和Apple市場下載安裝應用

2.打開SUNSKY App並掃描左側二維碼

SUNSKY APP
   ≥ 1 個 $10.87  
   ≥ 2 個 $10.77  
   ≥ 1/4 箱 $10.66  
   ≥ 1/2 箱 $10.55  
   ≥ 1 箱 $10.45  
   ≥ 4 箱 $10.34  
   ≥ 10 箱 $10.23  
選項:  
批量購買
添加到購物車
立即購買
國家/地區:
運費:   運輸方式:
其它方式
快遞 運費 運輸時間
Avatar
銷售經理: Ms. Grandy
+86-13824392739
+86-13824392739
+86-13824392739
我們一直努力做到低價和好的品質,並承諾保價和退換貨服務。
查看售後條款
IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
  • IP8F6403B
產品型號: IP8F6403B
Click Count 5393 點擊次數

特色產品

維修配件

最近瀏覽

免費禮物 (禮品將和當前產品一起發送)

描述

安裝前注意事項
提示1:安裝前
測試測試時,請勿取下任何保護膜或標籤。請注意靜電問題。
在嘗試任何修理之前,請確保自己接地是ESD(靜電放電)帶。這將防止靜電損壞手機內的电子元件。
確保您戴上護目鏡並小心不要用玻璃碎片割傷手指。
提示2:模擬測試
屏幕更換是非常脆弱的產品。我們強烈建議在安裝前進行測試 請模擬測試,這意味着手機分開,(主板 LCD或屏幕)連接音頻線和新的更換,開機,測試完成。如果測試正常,請安裝它。如果無法显示,請在第一時間聯繫我們。請不要強迫它安裝在手機上。一旦安裝了屏幕,我們將不負責任。
提示3:不要過度彎曲電纜
請確保LCD電纜不要過度彎曲。彎曲超過90度將導致黑色显示。

優點
1. 庫存量大,交貨快,可滿足大量採購計劃 。
2. 原裝頂級品質。
3. 完全適合和工作
4. 提供專業服務的質量保證。

關於產品
1. 替換iPhone 8的液晶屏 觸摸屏数字轉換器組件 。
2. 更換舊的,破損的,破裂的,損壞的。
3. 讓您的設備看起來比以往更清爽。
4. 完全適合和工作。
5. 每件商品在發貨前都經過檢查並處於良好狀態。
6. 強烈建議專業安裝。一旦安裝了屏幕,我們將不負責任。

規格與包裝:
通用
兼容性
包裹重量
單個產品重量 0.12kgs / 0.26lb
装箱数量 200
整箱重量 13.00kgs / 28.66lb
整箱尺寸 48cm * 38cm * 27cm / 18.9inch * 14.96inch * 10.63inch
銷量排名
#34 所屬類別: 維修配件
#1 所屬類別: 維修配件 »  iPhone 8 維修配件
#1 所屬類別: 維修配件 »  iPhone 8 維修配件 »  LCD屏
LCD is Bubble Bag Protected, we will not offer warranty for installation.

更多圖片

IP8F6403B
IP8F6403B
IP8F6403B
IP8F6403B
IP8F6403B
IP8F6403B
IP8F6403B
IP8F6403B
禮品將與訂單一起發送:
S-IP5G-0292

指南: iPhone 8 / 8 Plus Display Assembly Replacement

Use this guide to replace a cracked front panel or a broken LCD. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Pentalobe Screws

  • Opening the iPhone's display will damage its waterproof seals. If you do not replace the seals, your phone will no longer be water resistant.
  • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
  • Power off your iPhone before beginning disassembly.
  • Remove the two 3.5 mm pentalobe screws on the bottom edge of the iPhone.

Step 2 - Opening Procedure

  • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
  • Use a hairdryer or Adhesive Melting Bag and apply it to the lower edge of the phone for about 90 seconds in order to soften up the adhesive underneath.

Step 3

  • Apply a suction cup to the lower half of the front panel, just above the home button.
  • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Step 4

  • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
  • Insert an opening pick into the gap.
  • The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

Step 5

  • Slide the opening pick up the left edge of the phone starting at the lower edge and moving towards the volume control buttons and silent switch, breaking up the adhesive holding the display in place.
  • Stop near the top left corner of the display.
  • Do not try to pry the top edge of the display away from the rear case, as it is held in place by plastic clips that may break.

Step 6

  • Re-insert your tool at the lower right corner of the iPhone, and slide it around the corner and up the right side of the phone to separate the adhesive.
  • Don't insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.

Step 7

  • Gently pull up on the suction cup to lift up the bottom edge of the display.
  • Do not raise the display more than 15 Degree or you'll risk straining or tearing the ribbon cables connecting the display.
  • Pull on the small nub on the suction cup to remove it from the front panel.

Step 8

  • Slide an opening pick underneath the display around the top left corner and along the top edge of the phone to loosen the last of the adhesive.

Step 9

  • Slide the display assembly slightly down (away from the top edge of the phone) to disengage the clips holding it to the rear case.
  • Open the iPhone by swinging the display up from the left side, like the back cover of a book.
  • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.
  • Lean the display against something to keep it propped up while you're working on the phone.

Step 10

  • Remove four Phillips screws securing the lower display cable bracket to the logic board, of the following lengths:
    Two 1.3 mm screws
    Two 2.8 mm screws
  • Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.
  • Remove the bracket.

Step 11

  • Use the point of a spudger to pry the battery connector out of its socket in the logic board.
  • Bend the battery connector cable slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Step 12 - Display Assembly

  • Use the point of a spudger to pry the lower display connector out of its socket.
  • To re-attach press connectors like this one, press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
  • Use the point of a spudger to disconnect the second lower display cable.

Step 13

  • Remove the three 1.3 mm Phillips screws securing the bracket over the front panel sensor assembly connector.
  • Remove the bracket.

Step 14

  • Use the point of a spudger to disconnect the front panel sensor assembly connector.
  • Remove the display assembly.
  • During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

評論

平均分
4.9 星
4-5 星:
100%
3 星:
0%
1-2 星:
0%
購買這個產品並撰寫高質量的評論可以獲得10SUNSKY積分($0.20).
Fida*****gora
from Basel
Switzerland
  Order #: 2001015549   Color: White  
01/10/2020 17:57
Na**ga
from Martigny
Switzerland
  Order #: 1911206436   Color: Black  
12/17/2019 03:25
Geor*****7000
from PARIS 12
France
  Order #: 1910074838   Color: White  
11/25/2019 17:24
SUNSKY: Thanks for your trust.
回復者 peggy
Bigc*****tech
from Stafford
Australia
  Order #: 19092315104   Color: Black  
11/22/2019 15:05
Anselm*****ntino
from Varzea do Poco
Brazil
Order #: 1808175535   Color: Black  
11/12/2019 06:03
Eug*****984
from roma
Italy
  Order #: 1909292537   Color: Black  
10/08/2019 03:43
Eug*****984
from roma
Italy
  Order #: 1909292537   Color: Black  
10/08/2019 03:38
Alexa*****blec
from Selb
Germany
Order #: 1909085334   Color: Black  
09/08/2019 14:04
Ram****rba
from LA NEUVILLE CHANT D'OISEL
France
  Order #: 1903073937   Color: White  
05/08/2019 11:43
Pol****oyd
from Mondragone
Italy
  Order #: 1903195552   Color: White  
04/14/2019 08:55


運輸方式

請選擇數量和所在國家/地區,然後按[計算]。可以得到不同運輸方式的價格
國家/地區:

買家推薦


消息

發現價格
產品型號:
* 以較低價格出售的網址:
備註/詳細信息:
錯誤報告
產品型號:
錯誤網址:
* 輸入錯誤:
說明:
錯誤圖片:
(gif/jpg/png, 500KB max)
 
 
到貨通知訂閱

產品型號:
請留下您的电子郵件和姓名,我們會在此商品有貨時立即向您發送电子郵件和留言。
* 您的Email:
您的姓名:
* 數量:
[$10.66] 4.7英寸 iPhone 8 三合一液晶屏總成 國產友達屏
4.9 超出 5 基於 18 用戶評分