產品類別
批發: $7.77
一箱100個: $793.00 $761.00
在App中購買

掃描產品的二維碼直接購買。

按照以下步驟操作:

1.轉到Google和Apple市場下載安裝應用

2.打開SUNSKY App並掃描左側二維碼

SUNSKY APP
   ≥ 1 個 $7.93  
   ≥ 2 個 $7.85  
   ≥ 1/4 箱 $7.77  
   ≥ 1/2 箱 $7.69  
   ≥ 1 箱 $7.61  
   ≥ 4 箱 $7.54  
   ≥ 10 箱 $7.46  
選項:  
批量購買
添加到購物車
立即購買
國家/地區:
運費:   運輸方式:
其它方式
快遞 運費 運輸時間
Avatar
銷售經理: Ms. Yoyo
+86-15817361427
+86-15817361427
+86-15817361427
我們一直努力做到低價和好的品質,並承諾保價和退換貨服務。
查看售後條款
S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
  • S-IP5S-0048
產品型號: S-IP5S-0048
Click Count 79987 點擊次數

特色產品

維修配件

最近瀏覽

免費禮物 (禮品將和當前產品一起發送)

描述

關於產品
1. 用於iPhone 5S的替換LCD 框架 觸摸板数字轉換器組件
2. 更換舊的,破損的
3. 使您的設備看起來比以往更清晰 
4. 完全適合和工作
5. 每個項目有在發貨前已經過檢查並處於良好狀態
6. 強烈建議進行專業安裝。一旦安裝了屏幕,我們將不負責任

安裝前注意事項
1. 提示1:安裝前
測試時,請勿取下任何保護膜或標籤。請注意靜電問題。
在嘗試任何修理之前,請確保自己接地是ESD(靜電放電)帶。這將防止靜電損壞手機內的电子元件。
確保您戴上護目鏡並小心不要用玻璃碎片割傷手指。
2. 提示2:模擬測試
屏幕是非常脆弱的產品。我們強烈建議在安裝前進行模擬測試,這意味着手機分開,(主板 LCD或屏幕)連接音頻線和新的更換,開機,測試完成。如果測試正常,請安裝它。如果無法显示,請在第一時間聯繫我們。請不要強迫它安裝在手機上。一旦安裝了屏幕,我們將不負責任。
3. 提示3:不要過度彎曲電纜
請確保LCD電纜不要過度彎曲。彎曲超過90度將導致黑屏。

優點
1. 庫存量大,交貨快,可滿足大量採購計劃
2. 原裝頂級品質 
3. 完整的配合和工作
4. 提供專業的服務質量保證

規格與包裝:
通用
兼容性
常见规格
重量 29g
包裹重量
單個產品重量 0.10kgs / 0.22lb
装箱数量 100
整箱重量 8.00kgs / 17.64lb
整箱尺寸 50cm * 40cm * 40cm / 19.69inch * 15.75inch * 15.75inch
銷量排名
#230 所屬類別: 維修配件
#2 所屬類別: 維修配件 »  iPhone 5S 維修配件
#1 所屬類別: 維修配件 »  iPhone 5S 維修配件 »  液晶屏
LCD is Bubble Bag Protected, we will not offer warranty for installation.

更多圖片

S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
S-IP5S-0048
禮品將與訂單一起發送:
S-IP5G-0292

指南: iPhone 5s Front Panel Replacement

Use this guide to replace the cracked or broken screen on your iPhone 5s by swapping out the front panel. The front panel does not include the home button, front camera assembly, earpiece speaker, or the LCD shield plate. To reassemble your device, follow these instructions in reverse order.

Buy these parts and tools
Download Guide

Step 1 - Front Panel Assembly

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
  • Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.

Step 2

  • Power off your iPhone before beginning disassembly.
  • Remove the two 3.9 mm Pentalobe screws from either side of Lightning connector.

Step 3

  • In the following steps you will be pulling the display up out of the phone body. The display is composed of a glass screen and a plastic bezel with metal clips.
  • Regardless of the tool you use, you need to be sure you pull up the entire display.
  • If the glass begins to separate from the plastic, as shown in the first image, slide a plastic opening tool between the plastic frame and the metal phone body to pry the metal clips out of the case.
  • If you are reassembling a phone with a separated display bezel, you may want to place a thin strip of adhesive between the plastic bezel and the glass to keep the phone closed.

Step 4 - LCD Screen Opener Opening Procedure

  • The next two steps demonstrate using the LCD Screen Opener, a great tool for safely opening the iPhone 5s that we recommend for anyone doing more than one repair. If you aren't using the LCD Screen Opener, skip to step 5.
  • Close the handle on the LCD Screen Opener, opening the suction-cup jaws.
  • Place the bottom of your iPhone in between the suction cups, against the plastic depth gauge.
  • The top suction cup should rest just above the home button.
  • Open the handles to close the jaws of the LCD Screen Opener. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

Step 5

  • Hold onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front panel up from the rear case.
  • The LCD Screen Opener is designed to safely open your iPhone just enough to separate the pieces, but not enough to damage the home button cable.
  • Peel the two suction cups off your iPhone.
  • Skip the next three steps and continue on step 8.

Step 6 - Manual Opening Procedure

  • If you don't have an LCD Screen Opener, use a single suction cup to lift the front panel:
  • Press a suction cup onto the screen, just above the home button.
  • Be sure the cup is completely on the screen to get a tight seal.

Step 7

  • The front panel is attached with clips, and there are several ribbon cables connecting it to the rest of the phone. Your goal here is to release the clips and open the phone only enough to disconnect the cables. Go slowly and carefully to avoid damage.
  • Make sure the suction cup is firmly attached to the front panel assembly near the home button.
  • While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the home button end of the front panel from the rear case.
  • With a plastic opening tool, gently pry the edges of the rear case down, away from the front panel assembly, while you pull up with the suction cup.
  • Take your time and apply firm, constant force. The 5s front panel assembly is a much tighter fit than most devices.

Step 8

  • Do not try to completely remove the front panel assembly from the rear case, as there are several ribbon cables still attached at the top of the iPhone.
  • Pull the plastic nub to release the vacuum seal on the suction cup.
  • Remove the suction cup from the display assembly.

Step 9

  • Open the phone just enough to reveal the metal bracket covering the home button cable.
  • Do not open the phone too far or you risk damaging the home button cable, or the socket it plugs into. Keep the cable loose—if it is stretched taut, that's too far.
  • Only the phone's original home button assembly will be capable of using the Touch ID functionality. If you rip the cable, installing a new home button will only restore ordinary home button functions, not the Touch ID features.
  • Use the tip of a spudger to push the bracket free and remove it with tweezers.
  • During reassembly, be sure to orient the bracket so that the single-prong side faces the bottom of the phone and the side with two slits faces the battery.

Step 10

  • Use the tip of a spudger to pry the home button cable connector up out of its socket.
  • Be sure you're separating the cable connector from its socket, and not prying the entire socket up. The socket is on its own glued-down cable that can be pried up if you aren't careful.

Step 11

  • Once the connector has been released, pull the home button end of the assembly away from the rear case, using the top of the phone as a hinge.
  • Open the display to about a 90 degree angle, and lean it against something to keep it propped up while you're working on the phone.
  • Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
  • In a pinch, you can use an unopened canned beverage to hold the display.

Step 12

  • Remove the two 1.6 mm Phillips #000 screws securing the metal battery connector bracket to the logic board.

Step 13

  • Remove the metal battery connector bracket from the iPhone.

Step 14

  • Use the flat end of a spudger to gently pry the battery connector up from its socket on the logic board.
  • Be very careful to only pry up on the battery connector itself and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.

Step 15

  • Remove the following screws securing the front panel assembly cable bracket to the logic board:
  • One 1.7 mm Phillips #000 screw
  • One 1.2 mm Phillips #000 screw
  • One 1.3 mm Phillips #000 screw
  • One more 1.7 mm Phillips #000 screw
  • This 1.7 mm screw tends to not be attracted to a magnetized screwdriver. Take care not to lose it when removing.
  • It is especially important to keep track of your screws in this step for reassembly. Accidentally using the 1.3 mm screw or one of the 1.7 mm screws in the bottom right hole will result in significant damage to the logic board causing the phone to no longer boot properly.
  • Be careful not to over-tighten the screws, and don't force them. If they don't fit easily when you are securing them, they may be the wrong size.

Step 16

  • Remove the front panel assembly cable bracket from the logic board.

Step 17

  • Use the flat end of a spudger to disconnect the front-facing camera and sensor cable.

Step 18

  • While still supporting the front panel, disconnect the LCD cable connector.
  • When reassembling your phone, the LCD cable may pop off the connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery.

Step 19

  • Finally, disconnect the digitizer cable connector.

Step 20

  • Remove the front panel assembly from the rear case.

Step 21 - Earpiece Speaker

  • Remove the two screws securing the upper component bracket:
  • 4.0 mm Phillips #000
  • 2.3 mm Phillips #000
  • It is imperative that the right screws are inserted into their respective holes. Otherwise it may cause severe damage to the LCD during reassembly.

Step 22

  • Orient the phone as shown, with the home button on top and the earpiece speaker on bottom.
  • Gently dislodge the clip, near the bottom left corner of the earpiece speaker bracket, outwards from its recess on the front panel assembly.
  • Do not pry with excessive force, as the earpiece speaker bracket is fragile and malleable.
  • With a set of tweezers, shift the bracket to the left to unclip it.

Step 23

  • Remove the bracket from the display.

Step 24

  • Remove the earpiece speaker with a set of tweezers.
  • If you use your fingers, be very careful not to touch the gold contacts on the front panel. Finger oil can prevent good contact.

Step 25

  • Using the edge of a set of tweezers or a metal spudger, gently pry the earpiece speaker contact cable up, to separate this portion of the camera and sensor cable from the adhesive below.
  • Only pry directly under the earpiece speaker contacts—there are sensors and microchips that can be damaged by prying elsewhere.

Step 26

  • Use the point of a spudger to lift the ambient light sensor and proximity sensor out of their recess in the display assembly.
  • There is a small, square plastic and metal holder for the proximity sensor. This holder is essential for the proximity sensor to function correctly.
  • If replacing the proximity sensor make sure that the holder remains adhered to the back of the display. If it comes off with the old proximity sensor, remove it from the old sensor and use a tiny bit of adhesive to re-attach it to the back of the display.

Step 27

  • Use the flat end of a spudger to gently peel the front-facing camera portion of the cable away from the display assembly.

Step 28

  • If you are reattaching the same shield plate to a new display, there is no need to peel the cable assembly off the LCD shield plate. Skip this step.
  • Carefully peel the cable assembly off of the LCD shield plate to remove it from the display.
  • Be careful not to grab the digitizer cable while peeling up the front facing camera and sensor assembly cable.

Step 29 - Home Button Assembly

  • Unscrew the single captive Phillips #000 screw securing the home button cable.
  • The captive screw is fastened to the home button cable by a spring contact backing. During reassembly, ensure the contact is in the correct orientation—on the side of the screw nearest the LCD.

Step 30

  • Fold the home button cable down, out of the way of the home button bracket.

Step 31

  • Remove the two 1.4 mm Phillips #000 screws from the home button bracket.

Step 32

  • Remove the home button bracket from the display assembly.

Step 33

  • Wedge the the tip of a spudger underneath the home button cable assembly.
  • The home button cable is affixed by mild adhesive.
  • Gently work the spudger underneath the cable to separate the home button cable from the front panel assembly.
  • Do not remove the home button yet, as it is still attached to the front panel assembly.

Step 34

  • If necessary, remove the tape over the home button on the front side of your cracked front panel assembly.
  • Gently push the top left corner of the home button up away from the front panel.
  • Do not push the home button all the way through—you only need to get a corner free, so that you can pry it free with a spudger.
  • This membrane is very thin. If you feel like you're going to tear the button, apply heat and try again.

Step 35

  • Peel the home button the rest of the way off of the display by prying gently with a spudger.

Step 36

  • Remove the home button assembly from the front panel.

Step 37 - Front Panel

  • Remove the 2.7 mm Phillips #000 screw from the back of the display assembly.

Step 38

  • Remove two 1.2 mm Phillips screws from each side of the LCD frame (four total).
  • To avoid stripping the final screw, it may be helpful to first slightly loosen all four screws before removing any.

Step 39

  • Remove the LCD shield plate from the display assembly.
  • Front panel remains.

評論

平均分
4.7 星
4-5 星:
95%
3 星:
5%
1-2 星:
0%
購買這個產品並撰寫高質量的評論可以獲得10SUNSKY積分($0.20).
Red***ds
from Praha 6
Czech
  Order #: 1901096351   SKU: S-IP5S-0048B  
(最有幫助的評論)
04/10/2019 15:04
Mob****ess
from Ventspils
Latvia
  Order #: 1909104840   SKU: S-IP5S-0048B  
11/25/2019 06:56
MKh***fa
from victoria
Seychelles
Order #: 1908021556   SKU: S-IP5S-0048B  
11/25/2019 04:25
Anselm*****ntino
from Varzea do Poco
Brazil
Order #: 1809205541   SKU: S-IP5S-0048B  
11/12/2019 06:37
Eug*****984
from roma
Italy
  Order #: 1807122532   SKU: S-IP5S-0048B  
10/08/2019 05:18
Eug*****984
from roma
Italy
  Order #: 1807122532  
10/08/2019 05:16
Eug*****984
from Roma
Italy
  Order #: 1809232563   SKU: S-IP5S-0048B  
10/08/2019 05:02
Gu**35
from Leverkusen
Germany
  Order #: 1903103932   SKU: S-IP5S-0048B  
04/01/2019 14:17
TOR***RO
from roma
Italy
Order #: 1810101558   SKU: S-IP5S-0048B  
11/16/2018 12:08
Om****dhi
from Saudi Arabia
 
10/12/2018 09:03
SUNSKY: tHANKS
回復者 Hanna


運輸方式

請選擇數量和所在國家/地區,然後按[計算]。可以得到不同運輸方式的價格
國家/地區:

買家推薦


消息

發現價格
產品型號:
* 以較低價格出售的網址:
備註/詳細信息:
錯誤報告
產品型號:
錯誤網址:
* 輸入錯誤:
說明:
錯誤圖片:
(gif/jpg/png, 500KB max)
 
 
到貨通知訂閱

產品型號:
請留下您的电子郵件和姓名,我們會在此商品有貨時立即向您發送电子郵件和留言。
* 您的Email:
您的姓名:
* 數量:
[$7.77] iPhone 5S 國產材料液晶總成
4.7 超出 5 基於 300 用戶評分